AMT Guns forum

Forum Home Forum Home > Auto Mag Pistol > Pet loads
  New Posts New Posts RSS Feed - Load data for the 357 & 44 AMP
  FAQ FAQ  Forum Search   Register Register  Login Login

Load data for the 357 & 44 AMP

 Post Reply Post Reply Page  <1 234
Author
Message
pbcaster45 View Drop Down
180 Auto Mag
180 Auto Mag


Joined: 19 Feb 2019
Location: Oklahoma
Status: Offline
Points: 36
Post Options Post Options   Thanks (0) Thanks(0)   Quote pbcaster45 Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jul 2023 at 2:00am
Chronograph results for the previous load (I did change to the Winchester Large Pistol Primer)

Bullet: Barnes 225 gr. XPB (all copper hollow point)
Powder: Hodgdon H-110 20.0 grs.
Primer: Winchester Large Pistol
Case: Starline
OAL: 1.615
Average Velocity: 1357 fps
ES: 64
SD: 23

I think I might test Ramshot Enforcer with this bullet.
Back to Top
Pantera Mike View Drop Down
Callahan's Auto Mag
Callahan's Auto Mag


Joined: 20 Jan 2018
Status: Offline
Points: 786
Post Options Post Options   Thanks (0) Thanks(0)   Quote Pantera Mike Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jul 2023 at 3:50am
Originally posted by pbcaster45 pbcaster45 wrote:

Chronograph results for the previous load (I did change to the Winchester Large Pistol Primer)

Bullet: Barnes 225 gr. XPB (all copper hollow point)
Powder: Hodgdon H-110 20.0 grs.
Primer: Winchester Large Pistol
Case: Starline
OAL: 1.615
Average Velocity: 1357 fps
ES: 64
SD: 23

I think I might test Ramshot Enforcer with this bullet.

Enforcer apparently has a faster burn rate, similar to Alliant 2400. It would probably be more tolerant of lower charge weights than WW296/H110 is. 

The knock against WW296/H110 is that they are notably unsafe at reduced load weights. The manufacturer goes out of their way to admonish against such experimentation. Supposedly pressure spikes can result, with concomitant firearms damage a possible result.  Your load above seems well into this undercharge territory, save for the fact that your longer bullet apparently compresses the load, which can raise pressures, perhaps to a safe level. 

Thus, if you are seeking lightweight loads you would be better off with 2400. Enforcer seems to be a good match for 2400 although I wouldn’t assume that one could simply substitute equivalent powder charges between the two powders. You are definitely going into pioneer mode when developing loads using components that only recently came into existence. 

One has to pose the question, ‘why?’  Why risk damage to yourself or the gun when there are plenty of established recipes to follow?  I do understand the urge to try a bullet between the normally found 200 and 240 grain weights, and one could possibly extrapolate powder charges from known good data when using a bullet of an intermediate weight. But I would control my variables and only chase a single unknown. I would either try Enforcer with a known bullet weight, comparing chronograph results with test loads using a proven formula with one of the established powders, OR I would try an intermediate bullet weight with one of the established powders, extrapolating between the minimum loads for the weights above and below my test bullet. 

In the latter case, I would also create test loads with known bullet weights to compare my performance with the published data, since all data is produced using cut down rifle cases. You may be using Starline pistol brass which has been shown to deliver lower pressures for a given charge weight, and typically about a 100fps reduction versus the same weight in a cut-down rifle case.  

A chronograph is a key tool here. If the data says x grains gives y fps and your testing with different brass shows a similar reduction in velocity, you can slowly elevate your charge weight until you achieve the published velocity, and then tentatively apply that delta to loads of increased strength. 

All the while keeping an eye out for overpressure signs like flatted primers, or in more extreme cases, cocking pieces and bolts flying past your head!
Back to Top
Luc V. View Drop Down
Admin Group
Admin Group
Avatar

Joined: 09 Mar 2008
Location: Belgium
Status: Offline
Points: 1338
Post Options Post Options   Thanks (0) Thanks(0)   Quote Luc V. Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jul 2023 at 5:20pm
Just out of curiousity, I ran your data trough QuickLoad, looks like a safe "practise-target" load to me:
Why the change of primers, are the federals to much flat?
Ps, the charge should be compressed 112% full of the case capacity, and QL gives a velocity of 1352 fps, thats pretty close calculated...

Back to Top
pbcaster45 View Drop Down
180 Auto Mag
180 Auto Mag


Joined: 19 Feb 2019
Location: Oklahoma
Status: Offline
Points: 36
Post Options Post Options   Thanks (0) Thanks(0)   Quote pbcaster45 Quote  Post ReplyReply Direct Link To This Post Posted: 31 Jul 2023 at 5:38pm
Thanks for the QuickLoad data!  Ran out of Federal 155s!  Sometimes you have to use what you have! 

P.S.  The primers looked nice and rounded - normal pressure indications (for both primers).  I think the Winchester Large Pistol is hotter than the Federal 155 but not as hot as the CCI-350.
Back to Top
pbcaster45 View Drop Down
180 Auto Mag
180 Auto Mag


Joined: 19 Feb 2019
Location: Oklahoma
Status: Offline
Points: 36
Post Options Post Options   Thanks (0) Thanks(0)   Quote pbcaster45 Quote  Post ReplyReply Direct Link To This Post Posted: 21 Aug 2023 at 3:27pm

A 25-yard group with my final hunting load at 25 yards.  I wish I could brag about my amazing one-handed shooting ability, but this was off the bags and taking my time (probably 5 minutes!)  I was getting intermittent feeding jams earlier in the month but a very light buffing of the frame part of the feed ramp completely eliminated those (so light a before and after photo would have looked the same).  I still get maybe one stovepipe every 50 rounds but I'm pretty sure that's me being careless with my grip.  Sending the barrel assembly off for the Mag-Na-Port process next week - hope that works as well as Kent Lomont suggested!

My hunting load uses a very old lot of H-110 from the 90s (priced $11.75 a pound!) - haven't had a chance to check it with the chronograph yet but it's very accurate. 

It goes without saying... don't rest the barrel on the bags!



Back to Top
pbcaster45 View Drop Down
180 Auto Mag
180 Auto Mag


Joined: 19 Feb 2019
Location: Oklahoma
Status: Offline
Points: 36
Post Options Post Options   Thanks (0) Thanks(0)   Quote pbcaster45 Quote  Post ReplyReply Direct Link To This Post Posted: 15 Nov 2023 at 3:27pm
Sorry guys, I love experimenting with new loads - but I've decided to dial it back until the situation with new gun production is resolved.  It's a "Safe Queen" for now!  What a mess!
Back to Top
 Post Reply Post Reply Page  <1 234

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2023 Web Wiz Ltd.

This page was generated in 0.047 seconds.

 - amtguns.info All rights reserved